Honda Acty Fuel Filter
$30.00
Your fuel filter is probably 25 years old and allowing gunk into your carb stealing those precious few horsepower. Get this new filter installed not just for piece of mind but to keep you lines running clean.
*****UPDATE*****
After complaints we have switched suppliers so that the filter has the correct size nipple. Previous filters we sold (and others sell) have plastic nipples larger than stock and can make it almost impossible to get the fuel lines back on. 25 year old dried out rubber makes the issue even worse. From now on we will only sell the filters that are the correct size even if we have to charge a few dollars more.
Shipping
Shipping & Delivery
Vendor Info
Vendor Information
- Store Name: WILLpowered
- Vendor: WILLpowered
- No ratings found yet!
More Products
Honda Acty Wiring Harness For Aftermarket Stereo
These connectors are for Honda Acty trucks and Acty Vans(Street) with the 4 pin/2 pin, 4 pin/4 pin, 6 pin/4 pin or the 16 pin connectors. The 1990-1993 Acty trucks should be the 4/2 pin and 1994 and up should be the 4/4 pin. A 6 pin/4 pin connector is now supported and is usually connected to a clarion headunit, verify before ordering. Most Acty Vans (Street) will be the newly added 16pin. BE SURE TO VERIFY YOUR CONNECTIONS and select the correct size on check out. These connectors plug directly into your stock Acty harness and have 6″ of wiring that you can then splice/solder to the harness that comes with your aftermarket stereo.
Select options
This product has multiple variants. The options may be chosen on the product page
Willpowered Alternator for Honda Acty
If your alternator is under performing or has completely died then this product is for you. OEM alternators can be expensive and we have seen used ones(not even rebuilt) for over $200. These alternators have a 60A output which is the stock size for most of the trucks/vans.
We have custom uprated some alternators to 100A output (56A bench tested stock) if you have the need, please contact us directly to discuss because most people don’t need them. Uprated are currently being built and can be pre-ordered with about 2-3 week lead time.
These NOW FIT trucks WITH AC!!!!
Select options
This product has multiple variants. The options may be chosen on the product page
Acty van and Street rear mud flap
Honda Acty Oil Filter
Acty Exhaust Header
Here it is, the WILLpowered exhaust header for the Honda Acty EO7A 660cc engines. This will work for both trucks and vans. Dyno tested for 1-2 hp if the only modification performed but more can be expected if you had a clogged catalytic converter. If this is the only exhaust modification you do the exhaust sound is slightly more throaty without really being any louder.
Comes with new gaskets for both ends
Deletes catalytic converter
Bolts to stock locations
Off-road use only
WILLpowered Honda Acty Strut Rod Bushing
These strut rod bushings for the Honda Acty were developed in house for a softer setup than the typical Moog bushings. The softness is closer to stock so you will eliminate steering wheel shake and strut rod slap but the ride will be softer overall. These allow some flex but unless you are going for a full race suspension setup these probably better suit your needs. An alignment following installation is HIGHLY recommended even if you are driving with a big smile and no more steering shakes.
Related products
Acty Big brake kit
Here it is, a compete big brake kit with everything you need in one kit. Not only have we consolidated all the parts you need but we have been able to reduce the price compared to others considerably. For installation you can watch our YouTube video and don’t forget to put the bleed screw up which means the caliper labeled “R” will go on the left or passenger side and vice versa. This kit includes the following for pre-order with an expected ship date just before Christmas 2024:
(2) Red front calipers w/clips
(4) WILLpowered big brake ceramic pads
(2) Front rotors with black painted hubs
(2) WILLpowered brake spacers
(4) Extended length hex screws for rotors
(8) Extended length studs
Honda Acty pillar pod trim
Almost two years in the making, our Ronin Werks team has been working behind the scenes to develop these Acty pillar pod trims. We scanned real Honda trim that had been molded with pods to ensure an exact fit into your truck/van. Next, injection molding was the solution to get the quality and durability we insist on. The molding process creates a 95% finished product so customers may wish to paint, texture or trim the piece prior to final installation. We chose to keep the divers side a solid piece to maintain a finished look. To install the handle holes will need to be added prior to installation.
Honda Acty Suspension Kit P-1
WILLpowered Honda Acty Suspension kit Phase 1! The top 2 things we do to a truck when we get it besides basic maintenance and our shift kit is these two parts right here. Stiffer springs give about 3/4-1″ lift in the front which levels the truck paired with WILLpowered strut rod bushings. Strut rod bushings get rid of the death wobble at 50mph but also improve steering and eliminate that metal slap sound when going over small bumps.
For a limited time get both of these essential parts at the same time and save!
