Wideband O2 Sensor and Lite Controller
$105.00
Wideband O2 sensor and controller for use with our Acty EFI kits or any application requiring an O2 sensor and controller. The O2 sensor is a WILLpowered branded LSU 4.9 style O2 sensor with a spartan lite style controller.
Shipping
Shipping & Delivery
Vendor Info
Vendor Information
- Store Name: WILLpowered
- Vendor: WILLpowered
- No ratings found yet!
More Products
Honda Acty Fuel Filter
Your fuel filter is probably 25 years old and allowing gunk into your carb stealing those precious few horsepower. Get this new filter installed not just for piece of mind but to keep you lines running clean.
*****UPDATE*****
After complaints we have switched suppliers so that the filter has the correct size nipple. Previous filters we sold (and others sell) have plastic nipples larger than stock and can make it almost impossible to get the fuel lines back on. 25 year old dried out rubber makes the issue even worse. From now on we will only sell the filters that are the correct size even if we have to charge a few dollars more.
Honda Acty Carb Rebuild Kit
If you are having issues with your carburetor and low on power, we always recommend a deep clean of the carburetor as the first step. This kit has the seals and gaskets you need to make sure your carb is sealed back up and running. Other issues can be the solenoids found in our other product listings.
Honda Acty Rear Wheel Bearing Set
Honda Acty rear wheel bearing set with the option to buy to the inner cv trans seals at the same time. Often you will be removing the entire rear cv axle to get to these bearings so it is usually a good idea to have the trans seals on hand incase they get damaged while doing the job. Each wheel has 2 bearings, one on the inner and one on the outer.
Select options
This product has multiple variants. The options may be chosen on the product page
Honda Acty Rear Shocks
Honda Acty rear shocks. You know if you need them! easy install but a world of difference. Check our WILLpowered YouTube page for a quick tutorial on how to change these out. These are our new rear shocks which are actually pressurized as opposed to the stock ones which are not (we have a video showing the difference). While they are a great replacement for stock because of the slight added stiffness they also pair well with our front springs.
Price is for both rear shocks!
fit HA-1/2/3/4/5/6/7, HH-1/2/3/4/6/7
Related products
Acty Exhaust Header
Here it is, the WILLpowered exhaust header for the Honda Acty EO7A 660cc engines. This will work for both trucks and vans. Dyno tested for 1-2 hp if the only modification performed but more can be expected if you had a clogged catalytic converter. If this is the only exhaust modification you do the exhaust sound is slightly more throaty without really being any louder.
Comes with new gaskets for both ends
Deletes catalytic converter
Bolts to stock locations
Off-road use only
AMP’d Microsquirt ECU
The AMP’d MicroSquirt adds higher current capacity injector drivers, higher current capacity on its optioisolated input, and 4 user configurable option switches that activate on-board pullup resistors for applications that use hall or optical style crank and cam sensors. They can also be used to re-purpose digital switch (ALED and WLED) outputs to become logic level ignition outputs for applications that require 3 or 4 ignition outputs without having to solder resistors into the ECU case or wiring.
MicroSquirt is an entry-level, fully assembled ECU with varied applications targeting power sports, single cylinder all the way up to 8 cylinders with up to 2 fuel and 4 spark outputs. Over 40 different ignition modes are supported from mainstream applications like GM LS1, Ford Zetec, Bosch Motronic, and Chrysler Gen III Hemis to unusual modes like Renix Jeep and the Suzuki Swift GTI.
We recommend using the AMP’d MicroSquirt over the regular MicroSquirt for these scenarios:
- When using 6 injectors in the 8-10 ohm range, or 8 or more injectors
- On 6 or 8 cylinder distributorless ignition applications (we make it easy to control these in wasted spark)
- 4 cylinder sequential coil on plug
- Fuel only installations triggered off the negative terminal of an ignition coil
- 2 high impedance injector outputs – max peak current increased to 19 amps
- 2 dedicated spark outputs
- 2 general purpose on/off outputs – can be repurposed as spark outputs with switchable pull ups
- 1 PWM IAC output – can be repurposed as general purpose output
- 1 dedicated fuel pump output
- 2 variable reluctor conditioned inputs with switchable pull ups
- 1 optoisolated RPM input – max voltage and current increased
- 1 flex fuel or general purpose switched input
- 7 analog inputs
- Supports speed density, alpha-N (TPS based), or MAF based fuel and spark tables
- 0.66 microsecond injector pulse width resolution
- Allows blending multiple load types, including specialized mode for independent throttle bodies
- Supports a wide variety of OEM cam and crank position sensors
- Accelerator pump or model based acceleration enrichment
- Closed or open loop idle speed and boost control
- On/off nitrous control
- Wankel rotary support: 2 rotor engines with separate leading and trailing spark tables
- Staged injection
- Table switching
- 16 x 16 fuel tables
- 12 x 12 spark tables
- 2 step rev limiter (launch control) with no-lift shifting
- Wideband AFR target table
- Flex fuel sensor input
- Real time barometric correction (external sensor required)
- Sequential shift cut and air shifter control
Honda Acty Front Brake Rotors
Replace those rusty 25 year old rotors with these new ones. Fits all HA-3/4 trucks and HH-3/4 vans, sold in pairs (price is for 2 front rotors). The current batch of solid rotors ONLY has the holes for the mounting screw slightly misaligned. This means that the rotor will fit and work as it should but will ultimately be held on by just the rim and lugnuts (just like some other stock setups).
Cross Drilled rotors are designed for maximum efficiency under braking and look amazing while doing so. Mounting holes for Cross Drilled Rotors are 100% correct.
Honda Acty pillar pod trim
Almost two years in the making, our Ronin Werks team has been working behind the scenes to develop these Acty pillar pod trims. We scanned real Honda trim that had been molded with pods to ensure an exact fit into your truck/van. Next, injection molding was the solution to get the quality and durability we insist on. The molding process creates a 95% finished product so customers may wish to paint, texture or trim the piece prior to final installation. We chose to keep the divers side a solid piece to maintain a finished look. To install the handle holes will need to be added prior to installation.
Honda Acty Suspension Kit P-2
The P2 kit is the ultimate suspension rebuild kit for the Honda Acty at a discounted rate. This kit includes:
2 – Front struts (left and right)
2 – Rear shocks (left and right)
2 – 300 # front springs
4 – Strut rod bushings
These struts and shocks are only available at WILLpowered and slightly pressurized unlike the stock oil filled parts in your 25 year old truck or offered by others.
Titanium wheel studs for Honda
Titanium wheel studs that fit Honda branded vehicles but specifically designed for the Acty and Street. Lighter and stronger than our previous extended wheel studs they can be a unique addition to your vehicle. Laser etched with the Ryoku Kanji to symbolize the added strength.
Highly recommend using a wheel stud installer while installing otherwise you may damage whatever lugnut etc you are using for install.