Honda Acty Engine Mount kit
Original price was: $195.00.$150.00Current price is: $150.00.
Honda Acty engine mount kit for HA-3/4 and HH-3/4. Part numbers:
50820-SJ6-030
50810-SJ6-030
50805-SJ7-050
Please verify the part numbers are what you need for your vehicle and a manual transmission. If you are unsure please call before purchasing. Reduce engine vibration and noise be restoring your engine mounts to their factory new condition. We are offering these engine mounts as a pre-order and for the cheapest we will ever offer them. Expected shipping date is mid September 2026.
-23%
-23%
Shipping
Shipping & Delivery
Vendor Info
Vendor Information
- Store Name: WILLpowered
- Vendor: WILLpowered
- No ratings found yet!
More Products
6 AN x 5ft black hose with straight fittings
WILLpowered Honda Acty Strut Rod Bushing
These strut rod bushings for the Honda Acty were developed in house for a softer setup than the typical Moog bushings. The softness is closer to stock so you will eliminate steering wheel shake and strut rod slap but the ride will be softer overall. These allow some flex but unless you are going for a full race suspension setup these probably better suit your needs. An alignment following installation is HIGHLY recommended even if you are driving with a big smile and no more steering shakes.
Honda Acty Thermo Oil Switch
Honda Acty Transmission Case Seals
These are the seals for the cv axles where they enter the transmission. This is for both the left and the right seals for HA-1/2/3/4 as well as vans HH-1/2/3/4. If you need only one seal let us know but if one is bad, the other is surely on its way.
Note: the Acty Attack models have a different size seal on the passenger side to support the locking diff – these DO NOT fit the Attack model passenger side.
Cheap Acty Spark Plug Wires
These wires are the ones we were using previously that MAY RIP DURING REMOVAL!!!!!!! This is why they are $5. They work great installed and if you are careful while removing and pull from the black fitting they probably won’t rip, but you’ve been warned. For $5 it might be best just to get two sets. Honda Acty spark plug wires in red for HA-1/2/3/4 and HH-1/2/3/4. Our other sets are stronger and don’t rip but are more expensive.
Honda Acty Air Vent Solenoid
Related products
24 mm coolant connector with a 25 mm lip and 1/8 npt fitting, 68 mm in length
The 24 mm coolant connector by WILLpowered is designed with a 25 mm lip and 1/8 NPT fitting, making it suitable for connecting coolant hoses in car and truck engines. With a length of 68 mm, this connector provides a secure and reliable connection for optimal engine cooling performance. Built to high standards of quality, this product is a durable and essential component for maintaining the engine cooling system in top condition.
Coolant hose kit for Acty
Coolant hose kit for the HA-3/4 trucks from WILLpowered. New silicone hoses can replace the decades old rubber hoses that are leaking, dry rotted or that just look horrible. These come in Blue, Black and Red with an option for a full kit of 8 hoses or a “dress up” kit of the 4 most common and visible hoses.
Although 90% of vans will use all these hoses there are a few models that have one or two different hoses (models with floor heat etc). We would prefer you just don’t buy these for the van version to prevent passive aggressive social media comments.
Honda Acty Fuel Filter
Your fuel filter is probably 25 years old and allowing gunk into your carb stealing those precious few horsepower. Get this new filter installed not just for piece of mind but to keep you lines running clean.
*****UPDATE*****
After complaints we have switched suppliers so that the filter has the correct size nipple. Previous filters we sold (and others sell) have plastic nipples larger than stock and can make it almost impossible to get the fuel lines back on. 25 year old dried out rubber makes the issue even worse. From now on we will only sell the filters that are the correct size even if we have to charge a few dollars more.
Honda Acty pillar pod trim
Almost two years in the making, our Ronin Werks team has been working behind the scenes to develop these Acty pillar pod trims. We scanned real Honda trim that had been molded with pods to ensure an exact fit into your truck/van. Next, injection molding was the solution to get the quality and durability we insist on. The molding process creates a 95% finished product so customers may wish to paint, texture or trim the piece prior to final installation. We chose to keep the divers side a solid piece to maintain a finished look. To install the handle holes will need to be added prior to installation.
